In the article, we will consider the replacement of the pipelines of a car equipped with an anti-lock brake system
After performing work with depressurization of the brake system, it is necessary to bleed the brakes, as indicated in the article - Replacing the hydraulic unit of the ABS system of a Chevrolet Niva car
Replacing the tube to the left front brake
We install the car on a lift or inspection ditch and set the parking brake
Disconnect the battery terminals and remove the battery from the car
We loosen the wheel bolts and raise the car (if it is on a lift) to a height convenient for work
Remove the front wheel
Disconnect the brake pipe fitting from the left front brake hose
Install the plug in the hole of the hose.
Remove the brake hose clamp from the brake pipe fitting
We take out the split seal 1 from the hole in the mudguard
Disconnect the fitting of the brake pipe from the hydraulic unit and install the plug in the hole of the hydraulic unit
We unscrew the nut 3 fastening the noise-insulating sleeve 1
Remove the guide bracket 2 and remove the tube from the slot in the bushing
Pick up the phone from the car
We install the tube in the reverse order
Bleeding the brake system as described in the article - Replacing the hydraulic unit of the ABS system of a Niva Chevrolet
Replacing the tube from the adapter to the right front brake
We install the car on a lift or a viewing ditch
Removing the engine screen
Unscrew the fastening nuts of the adsorber bracket and move the adsorber to the side
Loosen the wheel bolts
Raise the car to a comfortable working height
Unscrew the nuts of the right front wheel and remove the wheel
Disconnect the brake pipe fitting from the right front brake hose
Install a plug in the hole of the hose
Remove the brake hose clamp from the brake pipe fitting
Disconnect fitting 3 of the tube to the right front brake 4 and install a plug in its hole
Unscrew the nuts and remove the two brackets 1 securing the tube to the body
Pick up the phone from the car
Tube part number 21230-3506540-55-0
Install the tube in the reverse order and bleed the brake system as described in the article - Replacing the hydraulic unit of the ABS system of a Niva Chevrolet car.
Replacing the tube to the right front brake
We install the car at the workplace, brake with the parking brake and turn off the ignition
Removing the engine screen
Disconnect fitting 3 of the tube to the right front brake 4
We install a plug in the hole of the tube from the adapter to the right front brake
Disconnect the brake pipe fitting to the right front brake from the ABS hydraulic unit
Install the plug in the hole of the hydraulic unit
We unscrew the nut 3 fastening the noise-insulating sleeve 1
Remove the guide bracket 2 and remove the tube from the slot in the bushing
Remove the tube from the plastic bracket and remove it from the car
Install the tube to the right front brake in reverse order
Bleeding the brake system as described in the article - Replacing the hydraulic unit of the ABS system of a Niva Chevrolet
Replacing the tube to the left rear brake hose
We install the car on a lift or inspection ditch and set the parking brake
Raise the car to a comfortable working height
Disconnect fitting 1 of the brake pipe from hose 3 of the left rear brake
Install a plug into the hole in the left rear brake hose
Remove the hose clamp 2 from the brake pipe fitting
Unscrew fitting 1 and disconnect the tube to the hose of the left rear brake from the tube to the left adapter
Install the plug in the hole of the tube
We unscrew five nuts of 2 brackets for attaching pipes to the car body, disconnect the straps from them and remove the brake pipe
The tube is installed in the reverse order, and we bleed the brake system
Replacing tubes to adapter
We install the car on a lift or inspection ditch and set the parking brake
Raise the car to a comfortable working height
Removing the engine screen
Disconnect fitting 2 of the brake pipe to the right or left adapter
We install a plug on the brake pipe to the rear brake hose
We lower the car if it was raised on a lift
Disconnect the brake pipe fitting to the right or left adapter from the ABS hydraulic unit
Install the plug in the hole of the hydraulic unit
We unscrew the nut 3 fastening the noise-insulating sleeve 1
Remove the guide bracket 2 and remove the tube from the slot in the bushing
Remove the tube from two plastic brackets 1 and remove it from the car
Part number of tubes: right 21230-3506560-50-0; left 21230-3506570-50-0
We install in the reverse order and bleed the brake system
